1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
>From 9c5fa914202d20756c56e0c4fd76035ed8f8ced8 Mon Sep 17 00:00:00 2001
From: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Date: Mon, 6 Aug 2007 08:31:14 +0200
Subject: [PATCH 1/1] Add gpio_mouse board setup to atstk1000 board
This patch adds a gpio_mouse_platform_data to the atstk1000 board code and
registers a gpio_mouse platform_device. This will enable a GPIO mouse on header
J1 on GPIO of the ATSTK1000 development kit. The board code is enabled/disabled
in menuconfig.
By connecting J1 (GPIO) to J25 (SWITCH) you can use the following keys to
simulate a mouse:
SW0: right
SW1: down
SW2: up
SW3: left
SW5: right button
SW6: middle button
SW7: left button
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
---
arch/avr32/boards/atstk1000/Kconfig | 16 ++++++++++
arch/avr32/boards/atstk1000/atstk1002.c | 48 +++++++++++++++++++++++++++++++
2 files changed, 64 insertions(+), 0 deletions(-)
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index 718578f..d99d4bd 100644
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -52,6 +52,22 @@ config BOARD_ATSTK100X_SPI1
GPIO lines and accessed through the J1 jumper block. Say "y"
here to configure that SPI controller.
+config BOARD_ATSTK1002_GPIO_MOUSE
+ bool "Configure gpio_mouse on GPIO J1 header"
+ depends on !BOARD_ATSTK1002_SW4_CUSTOM
+ help
+ Enable gpio_mouse board configuration on GPIO 0 to 7. Connecting a
+ 10-pin flat cable from J1 (GPIO) to J25 (SWITCH) will let a user give
+ mouse inputs using the the switches SW0 to SW7.
+
+ SW0: right
+ SW1: down
+ SW2: up
+ SW3: left
+ SW5: right button
+ SW6: middle button
+ SW7: left button
+
config BOARD_ATSTK1000_J2_LED
bool
default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index c958fd4..c7560e5 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -16,6 +16,7 @@
#include <linux/types.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
+#include <linux/gpio_mouse.h>
#include <video/atmel_lcdc.h>
@@ -100,6 +101,49 @@ static struct mci_platform_data __initdata mci0_data = {
.cs = 4,
};
+#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE
+static struct gpio_mouse_platform_data gpio_mouse0_data = {
+ .polarity = GPIO_MOUSE_POLARITY_ACT_LOW,
+ {
+ {
+ .up = GPIO_PIN_PB(2),
+ .down = GPIO_PIN_PB(1),
+ .left = GPIO_PIN_PB(3),
+ .right = GPIO_PIN_PB(0),
+ .bleft = GPIO_PIN_PB(7),
+ .bmiddle = GPIO_PIN_PB(6),
+ .bright = GPIO_PIN_PB(5),
+ },
+ },
+ .scan_ms = 10,
+};
+
+static struct platform_device gpio_mouse0_device = {
+ .name = "gpio_mouse",
+ .id = 0,
+ .dev = {
+ .platform_data = &gpio_mouse0_data,
+ },
+};
+
+static void __init add_device_gpio_mouse0(void)
+{
+ struct platform_device *pdev = &gpio_mouse0_device;
+ struct gpio_mouse_platform_data *data = pdev->dev.platform_data;
+
+ at32_select_gpio(data->up, 0);
+ at32_select_gpio(data->down, 0);
+ at32_select_gpio(data->left, 0);
+ at32_select_gpio(data->right, 0);
+
+ at32_select_gpio(data->bleft, 0);
+ at32_select_gpio(data->bmiddle, 0);
+ at32_select_gpio(data->bright, 0);
+
+ platform_device_register(pdev);
+}
+#endif
+
/*
* The next two functions should go away as the boot loader is
* supposed to initialize the macb address registers with a valid
@@ -269,6 +313,10 @@ static int __init atstk1002_init(void)
atstk1000_setup_j2_leds();
atstk1002_setup_extdac();
+#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE
+ add_device_gpio_mouse0();
+#endif
+
return 0;
}
postcore_initcall(atstk1002_init);
--
1.5.2.3
|
